Volkswagen Touran Service Manual: Two-Part Wash Primer
Two-Part Wash Primer -LHV 043 000 A2- |
The two-part wash primer is a zinc chromate-free,
phenol-free and acid-free two-component wash primer from our PVB
system. |
Passivizing properties provide excellent protection against
corrosion. |
For metallic base surfaces, especially for aluminum and
galvanized sheet steel |
Simple processing properties |
Bare sheet steel, cleaned and sanded |
Cleaned and sanded, galvanized/electrolytically zinced sheet
steel or soft aluminum |
Thoroughly sanded old primer or factory primer (excluding
thermoplastic coating) |
Surfaces prepared with two-part polyester products and then
sanded very fine. |
|
|
|
Pre-treatment of base surfaces: |
|
Carefully clean using Silicone Remover -LVM 020 000 A5- or
Silicone Remover, Long -LVM 020 100 A5-. |
|
|
|
|
Clean and sand factory or old paint, eliminate any potential
rust areas, and sand transitions to old paint. |
|
|
|
|
Use a suitable cleaning agent before reworking to ensure a
clean and residue-free surface. |
|
|
|
|
1:1 by volume with Two-Part Additional Solution -LHA 004 000
A2- |
|
Adjustment for spraying 8 to 10 hours at +20 C (68 F) |
Note
Set material must be processed on the same day. |
|
|
|
|
Processing viscosity 4 mm for +20 C (68 F), German
Industry Standardization 53211 |
Processing viscosity 4 mm gravity feed spraygun "Compliant"
and "HVLP": |
DIN 4 mm: 16 to 18 seconds |
|
|
|
|
Set spray nozzle (see manufacturer's information):
"Compliant" 1.2 to 1.4 mm. |
|
Set spray nozzle (see manufacturer's information): "HVLP"
1.3 to 1.5 mm. |
|
Set spray pressure (see manufacturer's information):
"Compliant" to 2.0 to 2.5 bar. |
|
Set atomizing pressure (see manufacturer's information):
"HVLP" 0.7 bar. |
|
|
|
|
The prescribed layer thickness is 8 to 12 mm. |
|
|
|
Air dry at +20 C (68 F) room temperature, can be sprayed
over after 30 minutes. |
WARNING
Due to possible adhesion impairment, forced drying
and IR drying are not possible. |
|
|
|
|
Can be sprayed over with two-part HS filler at +20 C (68
F) after ventilation time. |
Afterwards, can be painted over with: |
Water-based base paint and two-part HS clear coat |
Caution
Do not rework with polyester products, epoxy
products or water soluble products. |
Do not apply to thermoplastic coatings. |
Do not rework directly with water-based base paint
or two-part top coat. |
|
|
|
|
Personal Protective Equipment: |
Note the safety data sheets |
Wear the personal protective equipment during application |
|
|
|
Delivery Viscosity |
at least 60 seconds |
Flashpoint: |
above +23 C (73.4 F) |
VOC value: 2004/42/IIB(c)(780)780 |
The EU limit for this product
(product category IIB.c) in ready-to-use form is a maximum of 780 g/L
volatile organic compounds. The VOC value of this product in
ready-to-use form is a maximum of 780 g/L. |
Note
The yield was calculated taking into account the recommended
layer thickness and the procentual proportion of solid material
(without thinner). The corresponding processing losses were not
taken into account. |
|
|
|
Guaranteed shelf life of 24 months from date of manufacture.
Use no later than the date indicated on the label and store in
original container at +20 C (68 F). |
|
|
|
Definition:
One-Part Wash Primer -LVM 044 007 A2-, light gray
One-Part Wash Primer -LVM 044 171 A2-, dark gray
...
Adhesion Promoter (Glazing)
Definition:
Adhesion Promoter -ALO 822 000 10- (glazing)
Edition 06/2011
P ...
© 2016-2024 Copyright www.vwtouran.net | 0.0066