Volkswagen Touran Service Manual: Two-Part Steel Filling Paste Set

Volkswagen Touran Service Manual / General Paint Information / Original Products / Filling Paste / Two-Part Steel Filling Paste Set

Definition:

Two-Part Steel Filling Paste Set -DA 787 300 A2-

Edition 09/2012

Product Description

This filling paste is made of polyester and a metal powder mixture and is used to produce true-to-contour surfaces on highly stressed body surfaces. This filling paste works especially well as a replacement for lead-coated alluvial tin.

This filling paste is pliable and sandable while maintaining a high degree of firmness and temperature stability, which makes it especially suitable to be painted over.

Note

The Two-Part Hardener, Long -LVM 018 100 A2- must be used at temperatures over 30 C (86 F) and / or with a relative humidity over 80 %.

Application Instructions

Base Surface

Suitable base surfaces:

Steel

General metallic base surfaces

Galvanized sheet steel

Pre-treatment of base surfaces:

Carefully remove any grease and sand the base surface. The base surfaces must be prepared using the → Chapter "Pneumatic Brush Grinder Set -VAS6446-". This means down to the bare metal with P40 grit sandpaper. If necessary, clean the dirty surface once again and then remove any cleaning residue again using the brush grinder.

Clean once more using silicone remover before reworking.

Processing

Application type: Filling

Mixture ratio:

Both components are mixed in a ratio of 1 part by volume of hardener liquid and 2.5-3 parts by volume of powder or 10 grams of hardener liquid and 58 grams of powder to create a product that can be spread.

Note

Avoid using too much hardener liquid, since this can negatively affect the final strength and adhesion of the filling paste.

Curing Time:

The pot life is approximately four to six minutes at +20 C (68 F).

Reaction Temperature:

The reaction temperature requires at least +5 C (41 F).

Drying

Air Drying:

Cure using the short-wave IR heater.

Ventilate approximately 10 minutes at +20 C (68 F).

Pre-hardening: 10 minutes at approximately 50 C (122 F)

Hardening 1st step: 10 minutes at 75 C (167 F)

Hardening 2nd step: 10 minutes at 85 C (185 F)

Sanding compatibility

Use the body planer to remove excess material before the thermal final curing process.

Then use P80 grit dry sandpaper to sand the contours.

Reworking:

No restriction

Characteristics

Air Drying:	Powder + Hardener Liquid
Flashpoint:	Hardener	33 C (91.4 F)
	Powder	not applicable

Storage

The guaranteed shelf life is 12 months from the production date. Use no later than the date indicated on the label and store in original container at +20 C (68 F).

Storage Conditions

Store in a cool and dry place. Storage temperature +20 C (68 F).

Note

Use only in well ventilated spaces.

The wearing of protective gloves and dust masks is recommended.

The use of a grinding dust extractor is recommended.

Filling Paste

...

Two-Part Fine Filling Paste

Definition: Two-Part Fine Filling Paste -LSP 784 002 A2- Edition 06/2011 Product Description ...

Other materials:

Volkswagen Touran Owners Manual. Folding the backrests on the third row of seats back
Fig. 97 Folding the seats in the third row back First read and observe the introductory information and safety warnings Pull the loop on the side of the seat in the direction of the arrow . Fold the backrest back until it clicks into place. Check that the backrest is ...

Volkswagen Touran Owners Manual. Cleaning and changing windscreen wiper blades
Fig. 181 Changing the windscreen wiper blades Fig. 182 Changing the wiper blade for the rear window First read and observe the introductory information and safety warnings The factory-fitted windscreen wiper blades are coated with graphite. The graphite coating ensures that windscreen ...