Volkswagen Touran Service Manual: Plastic Cleaner
| Plastic Cleaner -D 195 850 A1- |
| Plastic Cleaner -D 195 850 A1- is a liquid universal cleaner
and thinner with an non-aromatic, low n-hexane content gasoline
base. The product contains no chlorinated hydrocarbons, and does
not corrode the paint if briefly contacted. |
| The Plastic Cleaner -D 195 850 A1- is mostly used to
degrease and clean base surfaces before the application of
adhesives or sealants. |
| Careful cleaning of the adhesion surfaces is essential for
proper adhesion and includes the removal of dust, oil and
grease. |
| Depending on the composition of the products listed above,
the cleaner can also be used to remove impurities and surplus
amounts of these materials as well as being used on various base
surface protection materials. |
| In some cases, the Plastic Cleaner -D 195 850 A1- is also
suitable for use as a thinner for certain adhesives/sealants as
coating compounds. It should be remembered that these products
are normally used undiluted. Thinning is only suitable in some
special processes or if a thinner consistency is desired. |
 Note
| Before starting to apply, it is necessary to read the safety
measures and advice in the safety data sheet. |
| Even for products which are not required to be labeled by
law, the usual safety measures must be observed for chemical
emissions. |
| Depending on the level of dirt present, the shape and size
of the parts to be cleaned, the Plastic Cleaner -D 195 850 A1-
can be applied and wiped off with either a brush or a cleaning
cloth. |
| To avoid contaminating the content of the original canister,
the cleaner should either be poured onto the cloth (do not press
the cloth onto the opening and tip the canister) or it should be
poured into a separate container (tin can etc.). |
| Only the amount needed for cleaning should be poured out and
the original canister should be closed again immediately. |
| The cleaned surfaces should be allowed to dry completely
(depending on circumstances 2 - 10 minutes) before the adhesive
or sealant is applied. |
| Blowing with compressed air can reduce the drying time but
in some cases the effect of cleaning can be negated by
compressed air with an oil content. |
| Base Surfaces with open pores should be allowed to dry for
at least 30 minutes before cleaning. When cleaning cut material
(for example, when inserting permanently glazed vehicle windows)
the processing guidelines of these products must be observed. |
|
|
|
| Color |
Water-bright, transparent |
| Odor |
Gasoline |
Antistatic Plastic Cleaner
| Antistatic Plastic Cleaner -LVM 001 001 A2- |
Note
| The usage and application instructions for the Antistatic
Plastic Cleaner -LVM 001 001 A2- are described in the
appropriate base components. |
| Possible Base Components Are: |
| → Chapter "Adhesion Promoter (Glazing)". |
| → Chapter "Two-Part Synthetic Adhesion Filler". |
|
|
|
Definition:
Silicone Remover -LSW 019 000 A5-, watery
Silicone Remover -LVM 020 000 A5-
Sil ...
Definition:
Industrial Dirt Remover -ABS 600 000 10-
Edition 05/2004
Product Description
...
Other materials:
Volkswagen Touran Owners Manual. Introduction
This chapter contains information on the following subjects:
→ Warning and indicator lamps
→ Using the cruise control system
The cruise control system (CCS) is able to maintain an individual set speed at
forward speeds between approx. 20 km/h (12 mph).
The CCS slows t ...
Volkswagen Touran Service Manual. Hoses, Repairing
General Information
A new repair concept has been developed for repairing washer
system hoses. Various individual hose connectors, adapters,
Ethylene Propylene Diene Methylene (EPDM) rubber hoses and
shrink tubing will be offered as replacement parts.
...
© 2016-2024 Copyright www.vwtouran.net | 0.0122
Silicone Remover
Industrial Dirt Remover